FLASHCLEAN® (FLORAKLEEN®)

Unique, high performance rinse and soil conditioner for all substrates and systems.

From rejuvenating houseplants to maximising yields and potential in commercial hydroponics, FlashClean® is one of the most powerful tools available to gardeners!

Eventually, every growing system will develop fertilizer residue as a natural part of the growing process. This accumulation results in salt build-up that can block drippers, cause unsightly accumulations on the top of soil or substrate, and will eventually cause your plants undue stress and even root damage. With the highly concentrated nutrients available today, and high EC levels running in many systems, nutrient lockout can also be an invisible limit on your grow; FlashClean® solves all these problems and more:

Dissolves accumulated fertiliser salts
Corrects nutrient balance
Treats nutrient lock out
Nourishes microbial life and refreshes soil and coco coir
Maximises final stage growth (especially with FinalPart®)

Specifically developed to dissolve mineral salts,FlashClean® releases nutrient bonds between minerals and substrate and allows you to rinse excess residue. This release also helps plants make the most of remaining fertilizers, especially in the crucial week just before harvest.

Unlike other “flushes” and finishing products on the market, FlashClean® is not an acid, isn’t enzyme based, and does not dump magnesium or other mineral additives into your system - this makes it uniquely flexible: with FlashClean® you can give your system, and your plants, a clean slate at any time and at any stage of the growth process.

No matter what type of growing system you’re using

- indoors or outdoors, soilless or hydroponic, pots or garden beds, FlashClean® is easy to use: just mix with pH adjusted water and apply.

How to use FlashClean®:

In recirculating hydroponic systems:

To reset and refresh before changing nutrients (inc. before FinalPart®): Add 1.5 to 3 ml / L of FlashClean® to your existing nutrient solution and circulate for 24 hours before draining and replacing with fresh nutrient solution. Use the lower dosage for young or fragile plants, and the higher dosage for established plants / close to harvest.
After nutrient burn or lock-out: Drain old nutrient solution, add 1.5 to 3 ml / L of FlashClean® to pH adjusted water (you don’t need to use a full tank, just enough to circulate freely and run the system). Circulate for 24 hours before draining and adding new, fresh nutrient solution. Use the lower dosage for young or fragile plants, and the higher dosage for established plants.
As a final rinse (after FinalPart®): Drain old nutrient solution, add 1.5 to 3 ml / L of FlashClean® to pH adjusted water (you don’t need to use a full tank, just enough to circulate freely and run the system). Circulate for for the last two days before harvest to increase sugar levels in your crop instead of losing aroma and medicinal content with a long water flush..

In potting soil & soilless mixes inc. Coco Coir:

To reset and refresh before changing nutrients (inc. before FinalPart®), and after nutrient burn or lock-out: Every fifteen days (or when needed after lock out etc): fill a watering can with fresh pH adjusted water and add 1.5 to 3 ml / L of FlashClean®. Drench until there is runoff from the bottom of the pot. Resume your regular fertiliser schedule with the next watering. Use the lower dosage for young or fragile plants, and the higher dosage for established plants.
As a final rinse / after FinalPart®: Use 3 ml / L of FlashClean® instead of nutrients during the last two days before harvest to increase the sugars level in your crop instead of losing aroma and medicinal content with a long water flush.

NB: FlashClean® can be used at any stage of growth or flowering but do not use FlashClean® more than once every two weeks.

Soluble 1lb. Trio Pack

Related products

Trikologic (Beneficial Microorganisms)

Rootit First Feed 125ml

PH down

FloraMicro HW